Видео

gonna need a video where you do electric fan conversion for the pin outs

This is one of the best videos I’ve seen on TCC. My case is 0CHM but doesn’t have any pressure ports on the passenger side. Says the transmission is from TBI 5.7 truck. So my next step will be to order the same kit you used. Thanks for a great video. You gained another subscriber today!

1/2 inch is 12.7 mm

Thanks for your help! Doing my first build and this helped a ton :)

When checking measurement do you tighten all the way down or just finger tight

Perfect videos my man!!

Thanks, helped a lot!

A que velocidad tiene que pasar la 2? Si 15 no y 25 no? Y la 4 marcha pasa ? Y a que velocidad

How is it holding up. I've been thinking about doing this myself for a while.

Isn't there a better way to wire it so you dont have to manually switch it on and off?

From Rockauto - Universal Drain PlugUniversal Drain Plug Kit for Automatic Transmissions. Easy to install and ends messy fluid spills. Great for fleet vehicles where frequent transmission fluid and filter changes are necessary. Includes: 1 Plastic Seal: 3/4" Outer Diameter, 1/2" Inner Diameter 1 Nut: 1/2" Inner Diameter 1 Bolt: 3/4" Diameter 1 Plug: 7/16" Note: Washer goes on the inside

Something you didn’t mention is the adjustment of the electric choke. You set it to closed. It needs to be set to about a credit card thickness. Otherwise it’s going to sputter like it did.

Thank you brother! Just switched out the gear, seal, and O ring. Mine had 2 seals in it, weird. Maybe for a reason. Hopefully, it does not leak.

Good teacher, your words were clear and concise and you covered all angles. Thanks.

Excellent tutorial 👍

Nice! Will try this on my mc. What punk song is it in the vid?

Does this work for the 200R4 as well?

Where you buy this harness? Need one for my 56, thanks

Best video ive seen yet. Very informative thanks so much.

You've got it wrong about the copper not showing on the inner bushing, it might be right in some cases but not in most.

I assume you are doing this with oil already in the engine to begin with!

Excellent and honest video! Ditto, this channel should be at the top of the food chain.

cool truck, been looking to run an actuator on mine, I have 1977 running gear on a 55 body. I can see the need for a manual lever.

This channel is soo underrated. 🔥 💩!!

did you use teflon tape ?

Nice work 👍🏾

👍

I did something Similar. I have a GenV LT1. So didn't have that oil port. I bought an Oil filter adapter that I could put my line into. My engine had not been rebuilt, just had been sitting for over a year. So I didn't want to start it dry. I just used the pump on the garden sprayer and pushed 3 or 4 quarts of oil into the engine. When I started it I had 60 PSI of pressure almost immediately.

Great job. For me, the way you edited this was right to the point, clear, and explored options. Thank you for spending the time to help me.🙏

Can a heidts subframe be used with the speedway kit?

Can I add this to Plastic Transmission Fluid Pan 2024 Nissan Frontier?

I like your music brap!

Thanks

Nice to see the products lost their shine. I've coated my truck chassis with POR 15. The thing I dislike about it the most is the gloss finish.

This is my first video I've watched of yours and You Rock Brother!

Thanks for the video man glad I found it

Great video thanks brother, gotta head over to ACE now 😎

🔥

We need another series bro!!

Are all pistons clocked the same? Or is it opposite for passenger side pistons?

How long can you do this prior to start up? I mean can you do this a month before start up and let it sit or does it need to be done just before start up? Thanks

Thanks man this really helped me tune my carb

bro building a 1985 ss 350/700r4 we found a hot wire for for excesseries 30 amp coming from fuse block we taped into always hot running down there when key is on we was told trans was one wire at factory plug ..and grounded can i wire it threw the brake lights like you did in your truck please help thank u

Great video

Can this be the same concept as fixing the main seal leak from my 1984 Buick Regal?

Howmuch oil do i use with this still the 6qt?

Finally! A how-to video on this subject that makes perfect sense

What bracket would I use for the JEGS stainless steel cable, and a TBI?

My inner tie rods won't seat in any tips to get them in?

Do all transmissions have a bushing like that?